/** * @file utilities.h * @author Lewis He (lewishe@outlook.com) * @license MIT * @copyright Copyright (c) 2025 Shenzhen Xin Yuan Electronic Technology Co., Ltd * @date 2025-04-30 * */ #pragma once // Note: // When using ArduinoIDE, you must select a corresponding board type. // If you don’t know which board type you have, please click on the link to view it. // 使用ArduinoIDE ,必须选择一个对应的板型 ,如果你不知道你的板型是哪种，请点击链接进行查看 // The model name with S3 after it is the ESP32-S3 version, otherwise it is the ESP32 version // 型号名称后面带S3的为ESP32-S3版本，否则是ESP32版本 // Products Link:https://www.lilygo.cc/products/t-sim-a7670e // #define LILYGO_T_A7670 // There are two versions of T-Call A7670X. Please be careful to distinguish them. Please check the silkscreen on the front of the board to distinguish them. // T-Call A7670X 有两个版本,请注意区分，如何区分请查看板子正面丝印. // #define LILYGO_T_CALL_A7670_V1_0 // There are two versions of T-Call A7670X. Please be careful to distinguish them. Please check the silkscreen on the front of the board to distinguish them. // T-Call A7670X 有两个版本,请注意区分，如何区分请查看板子正面丝印. // #define LILYGO_T_CALL_A7670_V1_1 // Products Link: https://lilygo.cc/products/t-sim-7670g-s3 #define LILYGO_T_SIM7670G_S3 // Products Link: https://lilygo.cc/products/t-a7608e-h?variant=42860532433077 // #define LILYGO_T_A7608X // Products Link: https://lilygo.cc/products/t-a7608e-h?variant=43932699033781 // #define LILYGO_T_A7608X_S3 // Products Link: https://lilygo.cc/products/t-sim7000g // #define LILYGO_SIM7000G // Products Link: https://lilygo.cc/products/t-sim7070g // #define LILYGO_SIM7070G // Products Link: https://lilygo.cc/products/a-t-pcie?variant=42335922094261 // #define LILYGO_T_PCIE_A767X // Products Link: https://lilygo.cc/products/a-t-pcie?variant=42335921897653 // #define LILYGO_T_PCIE_SIM7000G // Products Link: https://lilygo.cc/products/a-t-pcie?variant=42335921995957 // #define LILYGO_T_PCIE_SIM7080G // Products Link: ...... // #define LILYGO_T_PCIE_SIM7670G // Products Link: https://lilygo.cc/products/t-eth-elite-1?variant=44498205049013 // #define LILYGO_T_ETH_ELITE_A7670X // https://lilygo.cc/products/t-sim7600 // #define LILYGO_SIM7600X // Products Link: ...... // #define LILYGO_T_RELAY_S3_SIMSHIELD // SIMCOM standard interface series // #define LILYGO_SIM7000G_S3_STAN // #define LILYGO_SIM7080G_S3_STAN // #define LILYGO_SIM7670G_S3_STAN // #define LILYGO_A7670X_S3_STAN #if defined(LILYGO_T_A7670) #define MODEM_BAUDRATE (115200) #define MODEM_DTR_PIN (25) #define MODEM_TX_PIN (26) #define MODEM_RX_PIN (27) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (4) // The modem power switch must be set to HIGH for the modem to supply power. #define BOARD_POWERON_PIN (12) #define MODEM_RING_PIN (33) #define MODEM_RESET_PIN (5) #define BOARD_MISO_PIN (2) #define BOARD_MOSI_PIN (15) #define BOARD_SCK_PIN (14) #define BOARD_SD_CS_PIN (13) #define BOARD_BAT_ADC_PIN (35) #define MODEM_RESET_LEVEL HIGH #define SerialAT Serial1 #define MODEM_GPS_ENABLE_GPIO (-1) #define MODEM_GPS_ENABLE_LEVEL (-1) #ifndef TINY_GSM_MODEM_A7670 #define TINY_GSM_MODEM_A7670 #endif // It is only available in V1.4 version. In other versions, IO36 is not connected. #define BOARD_SOLAR_ADC_PIN (36) //! The following pins are for SimShield and need to be used with SimShield //! 以下引脚针对SimShield,需要搭配SimShield #define SIMSHIELD_MOSI (23) #define SIMSHIELD_MISO (19) #define SIMSHIELD_SCK (18) #define SIMSHIELD_SD_CS (32) #define SIMSHIELD_RADIO_BUSY (39) #define SIMSHIELD_RADIO_CS (5) #define SIMSHIELD_RADIO_IRQ (34) #define SIMSHIELD_RADIO_RST (15) #define SIMSHIELD_RS_RX (13) #define SIMSHIELD_RS_TX (14) #define SIMSHIELD_SDA (21) #define SIMSHIELD_SCL (22) #define SerialRS485 Serial2 #define PRODUCT_MODEL_NAME "LilyGo-A7670 ESP32 Version" #elif defined(LILYGO_T_CALL_A7670_V1_0) #define MODEM_BAUDRATE (115200) #define MODEM_DTR_PIN (14) #define MODEM_TX_PIN (26) #define MODEM_RX_PIN (25) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (4) #define BOARD_LED_PIN (12) #define LED_ON HIGH #define MODEM_RING_PIN (13) #define MODEM_RESET_PIN (27) #define MODEM_RESET_LEVEL LOW #define SerialAT Serial1 #define MODEM_GPS_ENABLE_GPIO (-1) #define MODEM_GPS_ENABLE_LEVEL (-1) #ifndef TINY_GSM_MODEM_A7670 #define TINY_GSM_MODEM_A7670 #endif #define PRODUCT_MODEL_NAME "LilyGo-T-Call A7670 V1.0" #elif defined(LILYGO_T_CALL_A7670_V1_1) #define MODEM_BAUDRATE (115200) #define MODEM_DTR_PIN (32) #define MODEM_TX_PIN (27) #define MODEM_RX_PIN (26) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (4) #define BOARD_LED_PIN (13) #define LED_ON HIGH // There is no modem power control, the LED Pin is used as a power indicator here. #define MODEM_RING_PIN (33) #define MODEM_RESET_PIN (5) #define MODEM_RESET_LEVEL LOW #define SerialAT Serial1 #define MODEM_GPS_ENABLE_GPIO (-1) #define MODEM_GPS_ENABLE_LEVEL (-1) #ifndef TINY_GSM_MODEM_A7670 #define TINY_GSM_MODEM_A7670 #endif #define PRODUCT_MODEL_NAME "LilyGo-T-Call A7670 V1.1" #elif defined(LILYGO_T_SIM7670G_S3) #define MODEM_BAUDRATE (115200) #define MODEM_DTR_PIN (9) #define MODEM_TX_PIN (11) #define MODEM_RX_PIN (10) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (18) #define BOARD_LED_PIN (12) #define LED_ON (LOW) // There is no modem power control, the LED Pin is used as a power indicator here. #define MODEM_RING_PIN (3) #define MODEM_RESET_PIN (17) #define MODEM_RESET_LEVEL LOW #define SerialAT Serial1 #define BOARD_BAT_ADC_PIN (4) #define BOARD_SOLAR_ADC_PIN (5) #define BOARD_MISO_PIN (47) #define BOARD_MOSI_PIN (14) #define BOARD_SCK_PIN (21) #define BOARD_SD_CS_PIN (13) #ifndef TINY_GSM_MODEM_SIM7670G #define TINY_GSM_MODEM_SIM7670G #endif #define MODEM_GPS_ENABLE_GPIO (4) #define MODEM_GPS_ENABLE_LEVEL (1) //! The following pins are for SimShield and need to be used with SimShield //! 以下引脚针对SimShield,需要搭配SimShield #define SIMSHIELD_MOSI (15) #define SIMSHIELD_MISO (7) #define SIMSHIELD_SCK (16) #define SIMSHIELD_SD_CS (46) #define SIMSHIELD_RADIO_BUSY (38) #define SIMSHIELD_RADIO_CS (39) #define SIMSHIELD_RADIO_IRQ (6) #define SIMSHIELD_RADIO_RST (40) #define SIMSHIELD_RS_RX (41) #define SIMSHIELD_RS_TX (42) #define SIMSHIELD_SDA (2) #define SIMSHIELD_SCL (1) #define SerialRS485 Serial2 #define PRODUCT_MODEL_NAME "LilyGo-SIM7670G-S3" #elif defined(LILYGO_T_A7608X) #define MODEM_BAUDRATE (115200) #define MODEM_DTR_PIN (25) #define MODEM_TX_PIN (26) #define MODEM_RX_PIN (27) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (4) #define BOARD_BAT_ADC_PIN (35) // The modem power switch must be set to HIGH for the modem to supply power. #define BOARD_POWERON_PIN (12) #define MODEM_RING_PIN (33) #define MODEM_RESET_PIN (5) #define BOARD_MISO_PIN (2) #define BOARD_MOSI_PIN (15) #define BOARD_SCK_PIN (14) #define BOARD_SD_CS_PIN (13) #define MODEM_RESET_LEVEL HIGH #define SerialAT Serial1 #ifndef TINY_GSM_MODEM_A7608 #define TINY_GSM_MODEM_A7608 #endif // only version v1.1 or V2 has solar adc pin #define BOARD_SOLAR_ADC_PIN (34) // 127 is defined in GSM as the AUXVDD index #define MODEM_GPS_ENABLE_GPIO (127) #define MODEM_GPS_ENABLE_LEVEL (1) //! The following pins are for SimShield and need to be used with SimShield //! 以下引脚针对SimShield,需要搭配SimShield #define SIMSHIELD_MOSI (23) #define SIMSHIELD_MISO (19) #define SIMSHIELD_SCK (18) #define SIMSHIELD_SD_CS (32) #define SIMSHIELD_RADIO_BUSY (39) #define SIMSHIELD_RADIO_CS (5) #define SIMSHIELD_RADIO_IRQ (34) #define SIMSHIELD_RADIO_RST (15) #define SIMSHIELD_RS_RX (13) #define SIMSHIELD_RS_TX (14) #define SIMSHIELD_SDA (21) #define SIMSHIELD_SCL (22) #define SerialRS485 Serial2 #define PRODUCT_MODEL_NAME "LilyGo-A7608X ESP32 Version" #elif defined(LILYGO_T_A7608X_S3) #define MODEM_BAUDRATE (115200) #define MODEM_DTR_PIN (7) #define MODEM_TX_PIN (17) #define MODEM_RX_PIN (18) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (15) #define BOARD_BAT_ADC_PIN (4) #define MODEM_RING_PIN (6) #define MODEM_RESET_PIN (16) #define BOARD_MISO_PIN (47) #define BOARD_MOSI_PIN (14) #define BOARD_SCK_PIN (21) #define BOARD_SD_CS_PIN (13) #define MODEM_RESET_LEVEL LOW #define SerialAT Serial1 #ifndef TINY_GSM_MODEM_A7608 #define TINY_GSM_MODEM_A7608 #endif // only version v1.1 has solar adc pin #define BOARD_SOLAR_ADC_PIN (3) // 127 is defined in GSM as the AUXVDD index #define MODEM_GPS_ENABLE_GPIO (127) #define MODEM_GPS_ENABLE_LEVEL (1) //! The following pins are for SimShield and need to be used with SimShield //! 以下引脚针对SimShield,需要搭配SimShield #define SIMSHIELD_MOSI (11) #define SIMSHIELD_MISO (10) #define SIMSHIELD_SCK (12) #define SIMSHIELD_SD_CS (45) #define SIMSHIELD_RADIO_BUSY (38) #define SIMSHIELD_RADIO_CS (39) #define SIMSHIELD_RADIO_IRQ (9) #define SIMSHIELD_RADIO_RST (40) #define SIMSHIELD_RS_RX (41) #define SIMSHIELD_RS_TX (42) #define SIMSHIELD_SDA (2) #define SIMSHIELD_SCL (1) #define SerialRS485 Serial2 #define PRODUCT_MODEL_NAME "LilyGo-A7608X-S3" #elif defined(LILYGO_T_A7608X_DC_S3) #define MODEM_DTR_PIN (5) #define MODEM_RX_PIN (42) #define MODEM_TX_PIN (41) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (38) #define MODEM_RING_PIN (6) #define MODEM_RESET_PIN (40) #define MODEM_RTS_PIN (1) #define MODEM_CTS_PIN (2) #define MODEM_RESET_LEVEL LOW #define SerialAT Serial1 #ifndef TINY_GSM_MODEM_A7608 #define TINY_GSM_MODEM_A7608 #endif // 127 is defined in GSM as the AUXVDD index #define MODEM_GPS_ENABLE_GPIO (127) #define MODEM_GPS_ENABLE_LEVEL (1) #define PRODUCT_MODEL_NAME "LilyGo-A7608X-DC-S3" #elif defined(LILYGO_SIM7000G) || defined(LILYGO_SIM7070G) #define MODEM_DTR_PIN (25) #define MODEM_RX_PIN (26) #define MODEM_TX_PIN (27) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (4) #define BOARD_LED_PIN (12) #define LED_ON (LOW) #define BOARD_MISO_PIN (2) #define BOARD_MOSI_PIN (15) #define BOARD_SCK_PIN (14) #define BOARD_SD_CS_PIN (13) #define BOARD_BAT_ADC_PIN (35) #define BOARD_SOLAR_ADC_PIN (36) #define SerialAT Serial1 #ifdef LILYGO_SIM7000G // Modem model:SIM7000G #ifndef TINY_GSM_MODEM_SIM7000SSL #define TINY_GSM_MODEM_SIM7000SSL #endif #define PRODUCT_MODEL_NAME "LilyGo-SIM7000G ESP32 Version" #endif #ifdef LILYGO_SIM7070G // Modem model:SIM7070G #ifndef TINY_GSM_MODEM_SIM7080 #define TINY_GSM_MODEM_SIM7080 #endif #define PRODUCT_MODEL_NAME "LilyGo-SIM7070G ESP32 Version" #endif // 127 is defined in GSM as the AUXVDD index #define MODEM_GPS_ENABLE_GPIO (48) #define MODEM_GPS_ENABLE_LEVEL (1) //! The following pins are for SimShield and need to be used with SimShield //! 以下引脚针对SimShield,需要搭配SimShield #define SIMSHIELD_MOSI (23) #define SIMSHIELD_MISO (19) #define SIMSHIELD_SCK (18) #define SIMSHIELD_SD_CS (32) #define SIMSHIELD_RADIO_BUSY (39) #define SIMSHIELD_RADIO_CS (5) #define SIMSHIELD_RADIO_IRQ (34) #define SIMSHIELD_RADIO_RST (15) #define SIMSHIELD_RS_RX (13) #define SIMSHIELD_RS_TX (14) #define SIMSHIELD_SDA (21) #define SIMSHIELD_SCL (22) #define SerialRS485 Serial2 #elif defined(LILYGO_SIM7600X) #define MODEM_DTR_PIN (32) #define MODEM_RX_PIN (26) #define MODEM_TX_PIN (27) #define MODEM_FLIGHT_PIN (25) #define MODEM_STATUS_PIN (34) #define BOARD_MISO_PIN (2) #define BOARD_MOSI_PIN (15) #define BOARD_SCK_PIN (14) #define BOARD_SD_CS_PIN (13) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (4) #define MODEM_RING_PIN (33) #define BOARD_LED_PIN (12) #define LED_ON (HIGH) #define BOARD_BAT_ADC_PIN (35) #define BOARD_SOLAR_ADC_PIN (36) #define SerialAT Serial1 #ifndef TINY_GSM_MODEM_SIM7600 #define TINY_GSM_MODEM_SIM7600 #endif // 127 is defined in GSM as the AUXVDD index #define MODEM_GPS_ENABLE_GPIO (127) #define MODEM_GPS_ENABLE_LEVEL (1) //! The following pins are for SimShield and need to be used with SimShield //! 以下引脚针对SimShield,需要搭配SimShield #define SIMSHIELD_MOSI (23) #define SIMSHIELD_MISO (19) #define SIMSHIELD_SCK (18) #define SIMSHIELD_SD_CS (32) #define SIMSHIELD_RADIO_BUSY (39) #define SIMSHIELD_RADIO_CS (5) #define SIMSHIELD_RADIO_IRQ (34) #define SIMSHIELD_RADIO_RST (14) #define SIMSHIELD_RS_RX (12) #define SIMSHIELD_RS_TX (13) #define SIMSHIELD_SDA (21) #define SIMSHIELD_SCL (22) #define SerialRS485 Serial2 #define PRODUCT_MODEL_NAME "LilyGo-SIM7600X ESP32 Version" #elif defined(LILYGO_SIM7000G_S3_STAN) || defined(LILYGO_SIM7080G_S3_STAN) \ || defined(LILYGO_SIM7670G_S3_STAN) || defined(LILYGO_A7670X_S3_STAN) \ || defined(LILYGO_SIM7600X_S3_STAN) #define MODEM_BAUDRATE (115200) // Default I2C communication pin, cannot be changed #define BOARD_SDA_PIN (3) #define BOARD_SCL_PIN (2) #define MODEM_DTR_PIN (7) #define MODEM_TX_PIN (4) #define MODEM_RX_PIN (5) #define MODEM_RING_PIN (6) /* * GPS communication pin. If the modem has GPS function, * NMEA data can be read through this IO. * If an external GPS module is used, the same GPIO is used for communication. * */ #define MODEM_GPS_RX_PIN (48) #define MODEM_GPS_TX_PIN (45) #define MODEM_GPS_PPS_PIN (17) // This IO is only used when using an external GPS module, such as A7670G+L76K GPS #define GPS_SHIELD_WAKEUP_PIN (0) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (46) // Analog pins are already connected to the ADC voltage divider circuit and cannot be used for other purposes #define BOARD_BAT_ADC_PIN (8) #define BOARD_SOLAR_ADC_PIN (18) // SD Socket pins #define BOARD_MISO_PIN (13) #define BOARD_MOSI_PIN (11) #define BOARD_SCK_PIN (12) #define BOARD_SD_CS_PIN (10) // Enable / disable power save mode (1 disabled, 0 enabled) #define BOARD_POWER_SAVE_MODE_PIN (42) // CAMERA_XXX_PIN is routed to the pin header and camera connector #define CAMERA_PWDN_PIN (-1) #define CAMERA_RESET_PIN (-1) #define CAMERA_XCLK_PIN (21) #define CAMERA_SIOD_PIN (1) #define CAMERA_SIOC_PIN (41) #define CAMERA_VSYNC_PIN (9) #define CAMERA_HREF_PIN (14) #define CAMERA_PCLK_PIN (37) #define CAMERA_Y9_PIN (40) #define CAMERA_Y8_PIN (39) #define CAMERA_Y7_PIN (38) #define CAMERA_Y6_PIN (36) #define CAMERA_Y5_PIN (16) #define CAMERA_Y4_PIN (47) #define CAMERA_Y3_PIN (15) #define CAMERA_Y2_PIN (35) #define SerialAT Serial1 // This board has connected the ADC circuit to the modem, and the battery voltage can be read via AT+CBC #define MODEM_CONNECTED_ADC_PIN #ifdef LILYGO_SIM7000G_S3_STAN // Modem model:SIM7000G #ifndef TINY_GSM_MODEM_SIM7000SSL #define TINY_GSM_MODEM_SIM7000SSL #endif // GPS antenna power control GPIO, this GPIO is the modem GPIO #define MODEM_GPS_ENABLE_GPIO (48) #define MODEM_GPS_ENABLE_LEVEL (1) #define PRODUCT_MODEL_NAME "LilyGo-SIM7000G-S3-Standard" #endif #ifdef LILYGO_SIM7080G_S3_STAN // Modem model:SIM7080G #ifndef TINY_GSM_MODEM_SIM7080 #define TINY_GSM_MODEM_SIM7080 #endif // GPS antenna power control GPIO, this GPIO is the modem GPIO #define MODEM_GPS_ENABLE_GPIO (5) #define MODEM_GPS_ENABLE_LEVEL (1) #define PRODUCT_MODEL_NAME "LilyGo-SIM7080G-S3-Standard" #endif #ifdef LILYGO_SIM7670G_S3_STAN // Modem model:SIM7670G #ifndef TINY_GSM_MODEM_SIM7670G #define TINY_GSM_MODEM_SIM7670G #endif // GPS antenna power control GPIO, this GPIO is the modem GPIO #define MODEM_GPS_ENABLE_GPIO (1) #define MODEM_GPS_ENABLE_LEVEL (1) #define PRODUCT_MODEL_NAME "LilyGo-SIM7670G-S3-Standard" #endif #ifdef LILYGO_A7670X_S3_STAN // Modem model:A7670G/A7670E/A7670SA #ifndef TINY_GSM_MODEM_A7670 #define TINY_GSM_MODEM_A7670 #endif // GPS antenna power control GPIO, this GPIO is the modem GPIO #define MODEM_GPS_ENABLE_GPIO (1) #define MODEM_GPS_ENABLE_LEVEL (1) #define MODEM_AUDIO_PA_ENABLE_GPIO (3) #define MODEM_AUDIO_PA_ENABLE_LEVEL (1) #define PRODUCT_MODEL_NAME "LilyGo-A7670X-S3-Standard" #endif #ifdef LILYGO_SIM7600X_S3_STAN // Modem model:SIM7600E/A/SA/G #ifndef TINY_GSM_MODEM_SIM7600 #define TINY_GSM_MODEM_SIM7600 #endif // MODEM aux power supply #define MODEM_GPS_ENABLE_GPIO (127) #define MODEM_GPS_ENABLE_LEVEL (1) #define MODEM_AUDIO_PA_ENABLE_GPIO (77) #define MODEM_AUDIO_PA_ENABLE_LEVEL (1) #define PRODUCT_MODEL_NAME "LilyGo-SIM7600X-S3-Standard" #endif //! The following pins are for SimShield and need to be used with SimShield //! 以下引脚针对SimShield,需要搭配SimShield #define SIMSHIELD_MOSI (11) #define SIMSHIELD_MISO (13) #define SIMSHIELD_SCK (12) #define SIMSHIELD_SD_CS (37) #define SIMSHIELD_RADIO_BUSY (15) #define SIMSHIELD_RADIO_CS (38) #define SIMSHIELD_RADIO_IRQ (14) #define SIMSHIELD_RADIO_RST (39) #define SIMSHIELD_RS_RX (40) #define SIMSHIELD_RS_TX (41) #define SIMSHIELD_SDA (3) #define SIMSHIELD_SCL (2) #define SerialRS485 Serial2 #elif defined(LILYGO_SIM7080G_S3) #define SerialAT Serial1 #define MODEM_BAUDRATE (115200) #define PWDN_GPIO_NUM (-1) #define RESET_GPIO_NUM (18) #define XCLK_GPIO_NUM (8) #define SIOD_GPIO_NUM (2) #define SIOC_GPIO_NUM (1) #define VSYNC_GPIO_NUM (16) #define HREF_GPIO_NUM (17) #define PCLK_GPIO_NUM (12) #define Y9_GPIO_NUM (9) #define Y8_GPIO_NUM (10) #define Y7_GPIO_NUM (11) #define Y6_GPIO_NUM (13) #define Y5_GPIO_NUM (21) #define Y4_GPIO_NUM (48) #define Y3_GPIO_NUM (47) #define Y2_GPIO_NUM (14) #define I2C_SDA (15) #define I2C_SCL (7) #define PMU_INPUT_PIN (6) #define BUTTON_CONUT (1) #define USER_BUTTON_PIN (0) #define BUTTON_ARRAY {USER_BUTTON_PIN} #define BOARD_PWRKEY_PIN (41) #define MODEM_DTR_PIN (42) #define MODEM_RING_PIN (3) #define MODEM_RX_PIN (4) #define MODEM_TX_PIN (5) #define SDMMC_CMD (39) #define SDMMC_CLK (38) #define SDMMC_DATA (40) #ifndef TINY_GSM_MODEM_SIM7080G #define TINY_GSM_MODEM_SIM7080G #endif //! The following pins are for SimShield and need to be used with SimShield //! 以下引脚针对SimShield,需要搭配SimShield #define SIMSHIELD_MOSI (11) #define SIMSHIELD_MISO (13) #define SIMSHIELD_SCK (12) #define SIMSHIELD_SD_CS (21) #define SIMSHIELD_RADIO_BUSY (48) #define SIMSHIELD_RADIO_CS (45) #define SIMSHIELD_RADIO_IRQ (8) #define SIMSHIELD_RADIO_RST (47) #define SIMSHIELD_RS_RX (2) #define SIMSHIELD_RS_TX (1) #define SIMSHIELD_SDA (44) #define SIMSHIELD_SCL (43) #define SerialRS485 Serial2 #define PRODUCT_MODEL_NAME "LilyGo-T-SIM7080G-S3-PMU" #elif defined(LILYGO_T_RELAY_S3_SIMSHIELD) #ifndef TINY_GSM_MODEM_A7670 #define TINY_GSM_MODEM_A7670 #endif #define BOARD_PWRKEY_PIN 46 #define MODEM_RX_PIN 9 #define MODEM_TX_PIN 3 #define MODEM_DTR_PIN 11 #define MODEM_RING_PIN 13 #define SerialAT Serial1 #define PRODUCT_MODEL_NAME "LilyGo-T-RelayShield" #elif defined(LILYGO_T_PCIE_A767X) #define LILYGO_T_PCIE #ifndef TINY_GSM_MODEM_A7670 #define TINY_GSM_MODEM_A7670 #endif // Modem GPIO 4 control gps enable #define MODEM_GPS_ENABLE_GPIO (4) #define MODEM_GPS_ENABLE_LEVEL (0) #define PRODUCT_MODEL_NAME "LilyGo-T-PCIE-A7670X" #elif defined(LILYGO_T_PCIE_SIM7000G) #define LILYGO_T_PCIE #ifndef TINY_GSM_MODEM_SIM7000SSL #define TINY_GSM_MODEM_SIM7000SSL #endif // Modem Physical pins 48 control gps enable #define MODEM_GPS_ENABLE_GPIO (48) #define MODEM_GPS_ENABLE_LEVEL (1) #define PRODUCT_MODEL_NAME "LilyGo-T-PCIE-SIM7000G" #elif defined(LILYGO_T_PCIE_SIM7080G) #define LILYGO_T_PCIE #ifndef TINY_GSM_MODEM_SIM7080 #define TINY_GSM_MODEM_SIM7080 #endif #define PRODUCT_MODEL_NAME "LilyGo-T-PCIE-SIM7080G" #elif defined(LILYGO_T_PCIE_SIM7600X) #define LILYGO_T_PCIE #ifndef TINY_GSM_MODEM_SIM7600 #define TINY_GSM_MODEM_SIM7600 #endif #define PRODUCT_MODEL_NAME "LilyGo-T-PCIE-SIM7600X" #elif defined(LILYGO_T_PCIE_SIM7670G) #define LILYGO_T_PCIE #ifndef TINY_GSM_MODEM_SIM7670G #define TINY_GSM_MODEM_SIM7670G #endif // Modem GPIO 4 control gps enable #define MODEM_GPS_ENABLE_GPIO (4) #define MODEM_GPS_ENABLE_LEVEL (1) #define PRODUCT_MODEL_NAME "LilyGo-T-PCIE-SIM7670G" #elif defined(LILYGO_T_ETH_ELITE_A7670X) #define LILYGO_T_ETH_ELITE #ifndef TINY_GSM_MODEM_A7670 #define TINY_GSM_MODEM_A7670 #endif // Modem GPIO 4 control gps enable #define MODEM_GPS_ENABLE_GPIO (4) #define MODEM_GPS_ENABLE_LEVEL (0) #define PRODUCT_MODEL_NAME "LilyGo-T-ETH-Elite-A7670X" #else #error "Use ArduinoIDE, please open the macro definition corresponding to the board above " #endif #ifdef LILYGO_T_PCIE #define MODEM_DTR_PIN (32) #define MODEM_RX_PIN (26) #define MODEM_TX_PIN (27) // The modem power switch must be set to HIGH for the modem to supply power. #define BOARD_POWERON_PIN (25) // The modem boot pin needs to follow the startup sequence. #define BOARD_PWRKEY_PIN (4) #define MODEM_RING_PIN (33) #define BOARD_LED_PIN (12) #define PMU_IRQ (35) #define LED_ON (LOW) #define SerialAT Serial1 #ifndef MODEM_GPS_ENABLE_GPIO #define MODEM_GPS_ENABLE_GPIO (-1) #endif #ifndef MODEM_GPS_ENABLE_LEVEL #define MODEM_GPS_ENABLE_LEVEL (-1) #endif #endif #ifdef LILYGO_T_ETH_ELITE #define ETH_MISO_PIN (47) #define ETH_MOSI_PIN (21) #define ETH_SCLK_PIN (48) #define ETH_CS_PIN (45) #define ETH_INT_PIN (14) #define ETH_RST_PIN (-1) #define ETH_ADDR (1) #define SPI_MISO_PIN (9) #define SPI_MOSI_PIN (11) #define SPI_SCLK_PIN (10) #define SD_MISO_PIN (SPI_MISO_PIN) #define SD_MOSI_PIN (SPI_MOSI_PIN) #define SD_SCLK_PIN (SPI_SCLK_PIN) #define SD_CS_PIN (12) #define BOARD_SDA_PIN (17) #define BOARD_SCL_PIN (18) #define ADC_BUTTONS_PIN (7) #define MODEM_RX_PIN (4) #define MODEM_TX_PIN (6) #define MODEM_DTR_PIN (5) #define MODEM_RING_PIN (1) #define BOARD_PWRKEY_PIN (3) #define GPS_RX_PIN (39) #define GPS_TX_PIN (42) #define BOARD_LED_PIN (38) #define LED_ON (HIGH) #define SerialAT Serial1 #ifndef MODEM_GPS_ENABLE_GPIO #define MODEM_GPS_ENABLE_GPIO (-1) #endif #ifndef MODEM_GPS_ENABLE_LEVEL #define MODEM_GPS_ENABLE_LEVEL (-1) #endif #endif #if defined(TINY_GSM_MODEM_SIM7670G) || defined(TINY_GSM_MODEM_A7670) || defined(TINY_GSM_MODEM_A7608) #define MODEM_REG_SMS_ONLY #endif // Invalid version // #define LILYGO_T_A7608X_DC_S3 // Power on/off sequence #if defined(TINY_GSM_MODEM_A7670) #define MODEM_POWERON_PULSE_WIDTH_MS (100) #define MODEM_POWEROFF_PULSE_WIDTH_MS (3000) #elif defined(TINY_GSM_MODEM_SIM7670G) #define MODEM_POWERON_PULSE_WIDTH_MS (100) #define MODEM_POWEROFF_PULSE_WIDTH_MS (3000) #elif defined(TINY_GSM_MODEM_SIM7600) #define MODEM_POWERON_PULSE_WIDTH_MS (500) #define MODEM_POWEROFF_PULSE_WIDTH_MS (3000) // T-SIM7600 startup time needs to wait #define MODEM_START_WAIT_MS (15000) #elif defined(TINY_GSM_MODEM_SIM7080) #define MODEM_POWERON_PULSE_WIDTH_MS (1000) #define MODEM_POWEROFF_PULSE_WIDTH_MS (1300) #elif defined(TINY_GSM_MODEM_A7608) #define MODEM_POWERON_PULSE_WIDTH_MS (1000) #define MODEM_POWEROFF_PULSE_WIDTH_MS (3000) #elif defined(TINY_GSM_MODEM_SIM7000SSL) || defined(TINY_GSM_MODEM_SIM7000) #define MODEM_POWERON_PULSE_WIDTH_MS (1000) #define MODEM_POWEROFF_PULSE_WIDTH_MS (1300) #endif #ifndef MODEM_START_WAIT_MS #define MODEM_START_WAIT_MS 3000 #endif